iPhone 7 Audio IC: How to Diagnose and Fix It (U3101, 338S00105)
This guide is for board-level repair technicians. A customer brings in an iPhone 7 or 7 Plus: the speaker button is grayed out during calls, the other side can't hear them, and the phone takes forever to boot. This is the well-known iPhone 7 audio IC fault, also called iPhone 7 loop disease.
Quick answer
The chip itself is usually fine. What fails is the connection between the C12 pad under the audio IC (U3101) and the trace in the board. The fix is to remove U3101, run a jumper from resistor R1103 to C12, reball the chip and put it back. Reflowing alone does not fix it.
Symptoms of an iPhone 7 audio IC problem
- The speaker button is grayed out during a call and can't be tapped. This is the most obvious sign.
- The record button in Voice Memos is grayed out, or tapping it does not start a recording.
- On a call, the other side can't hear you and you can't hear them.
- The phone takes several minutes to boot, or sits on the Apple logo.
A grayed-out speaker button and a Voice Memos record button that does nothing are the two most reliable signs of audio IC disease.
Three checks before you open the phone
- Voice Memos: open Voice Memos and tap the red record button. If nothing happens at all, it is the audio IC. If only the bottom microphone is bad, the recording starts and you get a flat line.
- Speaker button: unplug any headphones, disconnect Bluetooth, and place a call. If the speaker button on the call screen is grayed out, that confirms it.
- Test the microphones separately: record a voice memo while speaking at the bottom of the phone to test the bottom microphone, then record a video while speaking at the top of the phone to test the top microphones. This is Apple's own test. The iPhone has three microphones. If only one is silent and the speaker button is not grayed out, look at that one microphone. If several are silent together, it is the audio IC on the board.
Before you pick up the hot air, dial *#06# and confirm the IMEI shows. The baseband sits directly on the other side of the board from the audio IC, so you want to know it was working before the repair.
| What you see | What it is |
|---|---|
| Speaker button grayed out, Voice Memos won't record | Audio IC U3101 |
| No sound only on calls and voice memos, speaker button not grayed out | Bottom microphone |
| No sound only on Siri, FaceTime and front-camera video | Top front microphone |
| No sound only on rear-camera video | Top rear microphone |
| Slow boot only, all audio functions work | Check the home button flex and the front camera flex first |
The cause: a broken connection at the C12 pad
The iPhone 7 board flexes at the spot where the audio IC sits. Normal use is enough to slowly pull the pads under the chip away from the traces inside the board. What breaks is the master clock line on the C12 pad, not the chip.
- C12 runs through resistor R1103 (33.2 Ω) to the CPU.
- With the chip removed, measure the C12 pad on the board in diode mode. A reading of OL (open line) means this line is broken.
- F12, H12 and J12 in the same column 12 also break. H12 and J12 carry headphone audio for the Lightning port.
- Hairline cracks also show up under the D12 pad.
Part number and location (the iPhone 7 Plus audio IC is the same chip)

| Model | Audio IC part number | Board designator |
|---|---|---|
| iPhone 7 | 338S00105 | U3101 |
| iPhone 7 Plus | 338S00105 | U3101 |
- The iPhone 7 and 7 Plus use the same 338S00105. It sits on the board on the back side of the SIM connector.
- Don't confuse it with the small audio IC, 338S00220. 338S00220 is the speaker amplifier at U3301, U3402 and U3502, and it is not the cause of a grayed-out speaker button.
The iPhone 7 audio IC fix: the C12 jumper
For the full removal and refit procedure, follow iFixit's U3101 replacement guide. The key steps:
- Remove U3101 and clean the pads.
- Measure C12 in diode mode and confirm it reads OL.
- Scratch the trace between C12 and R1103, then run a fine enameled wire from R1103 to the C12 pad position.
- Reball the chip and solder it back on the board.
How many jumpers to run (iPhone 7 audio IC jumper)
C12 is mandatory. Run F12, H12 and J12 at the same time. The procedure is the same as for C12.
- With C12 alone, calls and recording come back.
- Without H12 and J12, Lightning headphones may still have no sound after the repair.
- If the D12 pad shows a crack, run a jumper from D12 to G12.
These pads do not need to be repaired if they come off:
| Pad | Repair it? | Why |
|---|---|---|
| A12, B12 | No | Ground pads |
| E12 | No, as long as C1 is still there | E12 is connected to C1 |
| K12, L12, M12 | No | No-connect pads |
| E5 | No | No-connect pad |
| D12, G12, J11, A5 | One of the four still connected is enough | These four are connected to each other |
Reball the original chip or fit a new one (iPhone 7 audio IC replacement)
If the original chip is intact, reball it and put it back. If the chip is damaged, replace it with 338S00105.
- The break is in the board trace, so the original chip is good in most cases. Reballing the original is safer than fitting a new chip: the solder balls on a new chip are harder to melt and need more heat.
- Too much heat reflows the baseband on the other side of the board, and the phone ends up on "Searching" or "No Service". Use a preheater and reball with leaded solder.
- This chip is very thin and easy to damage during removal. If that happens, fit a new 338S00105.
FAQ
Can I just reflow the chip without removing it?
No. The break is in a trace inside the board, not in a solder joint. A reflow only lets the broken ends touch for a while. The fault comes back within about a month, and you have added one more chance of disturbing the baseband on the other side.
Calls work after the repair, but Lightning headphones still have no sound?
Add the H12 and J12 jumpers. These two pads carry headphone audio for the Lightning port.
The phone won't turn on or won't charge after the repair. What do I check first?
Check three things in order. First, whether a jumper has broken or R1103 was nudged out of place. Second, whether C5627 is touching C3211; these two sit very close together. Third, the four power rails for the audio IC: PP1V8_VA on C3209, PP1V8_SDRAM on C3211, PP1V2_VD_FILT on C3217, and PP_VDD_BOOST on C3212.
The phone shows "Searching" or "No Service" after the repair?
The baseband on the other side reflowed during heating. It has to be removed and reballed.
The chip won't solder down?
Calibrate your hot air station first. When the real temperature is tens of degrees below what the display shows, the solder under the chip never melts.
Does a slow boot always mean the audio IC?
No. A torn home button flex or a faulty front camera flex also slows the boot. If all audio functions work, check those two flexes first.
Do the iPhone 8, 6S and 6 have this problem too?
This is the signature fault of the iPhone 7 and 7 Plus. On the iPhone 8 it is not a signature fault, but it does happen. When several microphones are silent together, check the audio IC first there as well. The signature fault of the iPhone 6 and 6 Plus is touch, and for the 6S and 6S Plus it is the backlight.
Our recommendations
- Run the Voice Memos test and the speaker button test first, and open the phone only once the fault is confirmed.
- Run all four jumpers in one go: C12, F12, H12 and J12. Add one from D12 to G12 if D12 is cracked.
- If the original chip is intact, reball it and put it back. If it is damaged, order 338S00105. It fits both the iPhone 7 and 7 Plus, and we stock it in New and Refurbished.
Images are illustrative; the chips are shown magnified. Logic board reference photo: Sonic8400 / Wikimedia Commons, CC BY-SA 4.0.
Apple and Samsung names are used for compatibility only; ICMend is not affiliated with them.