Charging IC restock · US duties included
Restock charging ICs at pack prices.
Single chips commonly sell for around $8–11 on marketplaces. Our 10- and 20-packs bring it down to about $0.78–$2.50 a chip, with real marking photos on every listing.
The restock list
Charging ICs to keep on the bench
Pick 5, 10 or 20 pieces per part. The per-chip price drops as the pack grows.

iPhone 7 / 7 Plus & iPad
≈ $0.84 a chip in a 20-pack
Choose a pack →
iPhone 8 / X / XR / XS / 11
≈ $2.37 a chip in a 20-pack
Refurbished from $11.04 / 5 pcs
Choose a pack →
iPhone 12 series & iPad
≈ $2.50 a chip in a 20-pack
Choose a pack →
iPhone 13 series
≈ $0.84 a chip in a 20-pack
Choose a pack →
iPhone 6S / SE (2016) & iPad
≈ $1.30 a chip in a 20-pack
Refurbished from $4.54 / 5 pcs
Choose a pack →
iPhone 6S / SE (2016) / 7
≈ $0.78 a chip in a 20-pack
Choose a pack →
iPhone 11 / 12 series
≈ $1.75 a chip in a 20-pack
Choose a pack →
iPhone 6S / SE (2016) / 7
≈ $1.30 a chip in a 20-pack
Refurbished from $5.19 / 5 pcs
Choose a pack →Quick reference
Which chip fits which iPhone?
Always confirm the marking on your board before ordering.
New
Brand-new, never soldered or installed, marked with the part number only. A small number of defects within a batch is possible, so check each chip before you mount it.
Refurbished
Pulled from used phone boards, then cleaned, re-balled and repacked. A lower-cost option on some parts, such as 1612A1, 1610A3 and 338S00105.
Keep the common ones in stock
Many micro-soldering techs keep a 20-pack of 610A3B for iPhone 7 Tristar jobs and a 10- or 20-pack of 1612A1 for Hydra jobs on iPhone 8 and newer, plus a pack of Tigris spares. Not sure about a marking? Email admin@icmend.com.
Technician FAQ
Charging repairs: what to check before you swap a chip
Collected from real repair threads on r/mobilerepair, r/phonerepair and r/Iphonerepair, plus common bench practice. Community advice is labelled as such; always confirm with your own measurements.
1Diagnose before you swap
A phone came in not charging. What should I check before pulling the charging IC?
Work from the cheapest, non-soldered parts toward the board:
- Read current with a USB meter, using a known-good cable on both a 5 W and a 20 W+ USB-PD adapter.
- Inspect and clean the port under the microscope: packed lint, bent retainer clips, green corrosion. Techs on r/mobilerepair report cleaning far more ports than they replace.
- Try a known-good battery and a known-good dock flex. Disconnect the battery first, every time.
- Check the battery and dock FPC connectors for pry damage or knocked-off parts.
Only suspect Tristar, Hydra, U2 or Tigris once the modular swaps fail.
How do I tell a Tristar / Hydra / U2 fault from a Tigris fault?
Tristar (610A3B, 1610A3), Hydra (1612A1) and U2 (1614A1, 1616A0) handle the USB lines, accessory ID and the charging handshake. Tigris (SN2400AB0, SN2611A0) is the battery charger and power-path IC.
- Charges only when powered off, or boots on the cable and then drops to almost no current once iOS loads: a classic Tristar / Hydra / U2 symptom.
- Won't charge in any state with a good battery: points more toward Tigris.
- Charges with the screen on, stops when it sleeps: community techs point at Tigris or the battery's BMS. Rule out the battery first.
Wireless charging works but wired is dead. Can it still be the charging IC?
Yes. Wireless charging skips the Lightning pins and the USB handshake, so it mainly tells you the battery can take a charge. If wired charging is dead, or sits around 5 V with only a fraction of an amp, the fault is on the wired input path: dirty or damaged port, a bad dock flex, parts on the dock FPC, or a Hydra / U2 that won't negotiate. Clean the port and fit a known-good dock flex first; if current still drops after the boot logo, the USB IC is the next suspect.
It stopped charging right after a battery or port replacement. Why?
Before blaming an IC, check the three usual causes:
- The new part is bad. Defective replacement batteries and dock flexes are common; re-test with the old part or a second unit.
- Connector damage. A battery plug not seated flat, a pry-damaged battery FPC, or a small part knocked off next to the connector.
- A live short during the swap. Fitting a dock flex with the battery connected can take out Tristar or Hydra.
One check shared on r/mobilerepair: with only the logic board and dock flex connected and a charger plugged in, measure DC voltage at the battery connector. A tech citing repair.wiki reported about 3.7 V as normal and under 2 V as pointing to Tristar.
What causes "This accessory may not be supported" or fake charging?
The warning means the phone can't finish identifying the accessory over the Lightning ID/data pins. Before any heat:
- Clean and inspect the port for debris, oxidation or a bent contact, and try a certified cable.
- Check Settings › Battery: Optimized Battery Charging can hold at 80% and look like a fault.
- Swap in a known-good dock flex and battery.
If the warning stays, especially if the phone charges while off or shows the bolt without gaining percentage, the USB control IC (1610A3, 610A3B, 1612A1, 1614A1, 1616A0) is the main board-level suspect, with Tigris next.
2Choosing the right chip
Can I use 610A3B in place of 1610A3 or 1610A1?
Community practice: many techs stock 610A3B (the iPhone 7 Tristar) as their main Tristar and report it working in place of 1610A1, 1610A2 and 1610A3 on iPhone 6, 6S, SE (2016) and some iPads. Reports going the other way (an older 1610A3 into an iPhone 7 board) are mixed, so don't rely on it. Hydra 1612A1 (iPhone 8 and newer) is a different part and is never a substitute for Tristar. Board revisions vary: read the marking on your board before ordering.
Which USB IC and Tigris go together on each iPhone?
Keeping both stages on the shelf stops a repair from stalling when a bad port or charger takes out more than one chip:
- 6S / 6S Plus / SE (2016): 1610A3 Tristar + SN2400AB0 Tigris
- 7 / 7 Plus: 610A3B Tristar + SN2400AB0 Tigris
- 8 / X / XR / XS: 1612A1 Hydra (check your board's marking for the Tigris)
- 11 series: 1612A1 Hydra + SN2611A0 Tigris
- 12 series: 1614A1 U2 + SN2611A0 Tigris
- 13 series: 1616A0 U2
Always confirm the laser marking on the board you're working on.
Why keep 338S00105 audio codecs next to the charging chips?
On iPhone 7 / 7 Plus, the 338S00105 audio codec is at the center of the widely reported "loop disease": board flex breaks the pad under the chip (commonly cited as C12). Symptoms include a greyed-out speaker button on calls, Voice Memos not working, freezes, and a slow boot or restart loop that's easy to mistake for a battery or charging fault. The repair is to lift the codec, jumper the broken pad and mount a new chip. The baseband sits on the other side of the iPhone 7 board, so keep heat time short.
3Installing it safely
How do I swap Tristar, Hydra or U2 without killing the new chip?
Too much heat for too long is the usual reason new ICs and neighbours die. Every station has its own temperature curve, so treat numbers as starting points: techs commonly report around 330–380 °C for small BGA removal, and 315–350 °C with low airflow when mounting with 183 °C leaded paste.
- Shield nearby connectors, underfilled chips and shield edges with Kapton tape or an aluminium heat sink.
- Level the pads with 138 °C low-melt solder and flux-soaked wick instead of scraping.
- Clean with high-strength isopropyl alcohol and let the board cool fully before you power it up.
What's the "let the board drop" trick for pulling Hydra on sandwich boards?
On iPhone X and newer stacked boards, long heating risks separating the board layers or disturbing underfilled chips. A technique shared on r/mobilerepair: flux the chip, grip it lightly with tweezers, and hold the board slightly above the holder by the chip. Heat evenly; when the solder melts, the board drops back onto the fixture under its own weight and the old IC stays in your tweezers. No prying, and less heat soaked into the board. Reported settings in that thread varied widely, so use the ranges above as a guide.
How should I check and store BGA chips before soldering?
Heated chips can't be returned, so check every chip when the parcel arrives:
- Under the microscope, compare the laser marking with your boardview and find the pin-1 dot.
- Flip it: balls should be even, with no bridges, gaps or oxidation.
- Before mounting, measure the board pads in diode mode (red probe on ground). A reading near 0.000 means a short that would kill the new chip; fix it first.
Keep unused chips sealed in anti-static packaging, somewhere dry.
4Ordering from ICMend
What's the difference between New and Refurbished?
New: brand-new, never soldered or installed, marked with the part number only. A small number of defects within a batch is possible, so check each chip before mounting it.
Refurbished: pulled from used phone boards, then cleaned, re-balled and repacked. Among the parts on this page it's offered on 1612A1, 1610A3 and 338S00105; the rest are New only.
Every listing shows real photos of the chip marking. Not sure it matches your board? Email admin@icmend.com with a photo before you order.
What if a chip arrives dead, damaged or wrong?
Report it within 7 days of delivery with photos of the package and marking plus a short video or measurement, and we'll send a replacement or refund. Chips that have been soldered, tinned, re-balled or heated can't be returned, so run the arrival checks above first. Returns & Warranty Policy
How do pack prices and US shipping work?
Every part comes in packs of 5, 10 or 20, and the per-chip price drops as the pack grows: about $0.78–$2.50 a chip on the 20-packs above. For comparison, single charging ICs commonly sold for around $8–11 in our October 2026 sample of eBay sold listings.
Orders ship from Shenzhen in 1–3 business days, with US import duties included on both options: Economy Tracked, 7–15 days, $4.95, free over $59; Express by DHL, FedEx or UPS, 5–7 business days, $12.95, free over $129.
Build a $59+ restock order and Economy shipping is free.
Duties included for US repair shops. Ships from Shenzhen in 1–3 business days.