Charging ICs

iPhone Charging IC Diagnosis: Is It the Tristar, Hydra or Tigris?

By ICMend Team · Nov 2026 · 5 min read

iPhone 7 logic board with 610A3B, 1612A1 and SN2400AB0 charging ICs

This guide is for board-level repair technicians. When an iPhone won't charge and you've already ruled out the cable, the charging port flex and the battery, the fault is in an iPhone charging IC on the logic board. There are two kinds, and you need to know which one failed:

  • Tristar / Hydra (U2 IC): manages the Lightning port. It identifies what is plugged in and decides whether charging is allowed. It does not charge the battery.
  • Tigris: the chip that actually charges the battery.
610A3B Tristar and SN2400AB0 Tigris charging ICs, ball side up
Left: 610A3B (Tristar, 6×6 balls). Right: SN2400AB0 (Tigris), the larger package.

Quick answer: which IC to check first, by symptom

Symptom Check first Check next
No response when plugged in, ammeter reads 0 or below 0.1A Charging port flex, battery Tristar / Hydra
Shows the charging icon but the percentage doesn't rise (fake charging) Tristar / Hydra Tigris
Only charges when off, won't charge when on Tristar / Hydra Tigris
Charges wirelessly but not with a cable Charging port flex Hydra (Tigris is most likely fine)
5V is present at the charging IC input but the battery won't charge Tigris —
Battery stuck at 80% Battery Hydra

Here is how to handle each one.

Rule out three things before you touch the board

  1. Test with a known-good cable and power adapter.
  2. Try another charging port flex.
  3. Swap in a known-good battery.

If all three are ruled out and it still won't charge, move on to the ICs.

Step 1: narrow it down in three minutes with an ammeter and a multimeter

Follow this test procedure:

  1. Measure charging current with a USB ammeter. Normal draw is 0.8–1.6A. A reading of only 0.1–0.2A is also normal when the battery is dead flat or full.
  2. If the reading is 0 or below 0.1A, fit another charging port flex and retest. If that doesn't change it, swap the battery and retest.
  3. If it still won't charge after both swaps, measure the voltage on the leftmost pin of the battery connector on the board. Below 2V, replace Tristar.

No response when plugged in

After Step 1, if the battery connector voltage is below 2V, replace Tristar / Hydra.

To confirm on the board, measure these points:

  • Tristar models (iPhone 6–7): PP_5V0_USB and PP_TRISTAR_PIN should read 5V.
  • Hydra models (iPhone 8–11): PP_VBUS1_E75 should read 5V.
  • PWR_GATE_EN_VBUS_1_VALID test point: 3.7–5V means the USB IC is working. 0V means the USB IC is bad or has no power.

iPhone charging but percentage not increasing

This is fake charging. Check Tristar first.

  • Fake charging is usually a Tristar fault, so start with the lines from the charging port to Tristar.
  • If a new Tristar changes nothing, check Tigris next. On an iPhone 7, for example, measure capacitor C2105: with Tigris working normally in charge mode, pin 1 should read about 9V (2x VDD_MAIN).
  • Look at both chips together. Tristar has to give Tigris the go-ahead before charging actually happens, and a bad Tigris can take Tristar out with it. Keep both chips on hand for this repair.

An iPhone 6S not charging or an iPhone 7 not charging can both turn out to be fake charging. Work through them in the order above.

iPhone only charges when off

Check Tristar first. Charging only when off, or only when on, is a common sign of a bad Tristar.

If a new Tristar doesn't fix it, check Tigris next.

iPhone charges wirelessly but not with cable

Replace the charging port flex first, then check Hydra. Tigris is most likely fine.

  • Wireless charging skips the USB identification step, so working wireless charging tells you the charging IC is most likely fine and the problem is on the USB side.
  • The fault can be the charging port or Hydra, and you can't tell which without trying another port flex.

For an iPhone 11 not charging with this symptom, order 1612A1 for the USB side.

iPhone stuck at 80 percent

Swap the battery first, then check Hydra. There are two possible causes: a damaged gas gauge circuit in the battery, or a bad Hydra. A new battery tells them apart.

Is a Tristar tester useful?

Yes, but it only tests the Lightning port side. It takes a set of diode-mode readings on the charging port lines and compares them with stored good readings. Abnormal readings point to a fault on the Tristar / Hydra side. It cannot test Tigris.

The Tristar tester passes but the phone still won't charge. What now?

Check Tigris. A pass only means the path from the Lightning port to Tristar / Hydra is good. The tester cannot see Tigris, the chip that charges the battery.

Which chip to order, by model

  • iPhone 7 not charging: order 610A3B for the USB side and SN2400AB0 for the charging side.
  • iPhone 8 not charging, iPhone X not charging, iPhone XR not charging: the USB side is Hydra, so order 1612A1. We don't carry the Tigris IC for these models.
  • iPhone 11 not charging: order 1612A1 for the USB side and SN2611A0 for the charging side.

The full chart is below.

iPhone charging IC chart by model

Part numbers and board designators follow our product pages.

Model USB side (Tristar / Hydra / U2 IC) Battery charging side (Tigris IC) USB-PD fast charging IC
iPhone 6 / 6 Plus 1610A2 / U1700 SN2400B0 / U1401 —
iPhone 6S / 6S Plus / SE (2016) 1610A3 / U4500 SN2400AB0 / U2300 —
iPhone 7 / 7 Plus 610A3B / U4001 SN2400AB0 / U2101 —
iPhone 8 / X / XR / XS 1612A1 / U6300 Not in our store CPD2 / U6200
iPhone 11 series 1612A1 / U6300 SN2611A0 / U3300 CPD2 / U6200
iPhone 12 series 1614A1 / U9300 SN2611A0 / U4000 2E4B
iPhone 13 series 1616A0 / U9300 338S00770 2E4B
iPhone 14 series Not in our store 338S00839 2E4B
iPhone 15 / 16 series SN2012027 — —

On iPhone 6–7, a newer Tristar revision can replace an older one. See our Tristar compatibility chart.

Our recommendations

  1. Run the current and voltage checks in Step 1 before you decide which IC to pull.
  2. For fake charging and for phones that only charge when off, keep both Tristar and Tigris in stock.
  3. Once you know which chip failed, order the matching part number from the model chart above.

Images are illustrative; chips are shown enlarged. Logic board reference photo: Sonic8400 / Wikimedia Commons, CC BY-SA 4.0.

Apple and Samsung names are used for compatibility only; ICMend is not affiliated with them.

Can’t find your marking? Send us a photo

Send us the marking and a photo of the board. We source from the Huaqiangbei market and add the chip to the catalog.